encoches

Kit d'attache de ligne AMS EverGlide Safety Slides Kit pour flèches 5/16 (vendu en pack de 2). Kit permettant d'attacher une ligne sur une flèche de pêche à l'arc.

Caractéristiques :

- Système indispensable pour un bon guidage de la flèche en toute sécurité.
- Vendu par pack de deux.

Stringflex propose une encoche à capuchon pour les tubes en bois de diamètre 5/16 et 11/32 qui se fixe au tube sans avoir besoin de colle. Le système, qui est installé directement le tube sans coner le fut, est auto-centré, donc d'une précision absolue. Comme de nombreux produits en ligne Stringflex, l'encoche pour tiges de bois est une solution simple, propre et précise. En quelques secondes, vous pouvez préparer une douzaine de tubes avec encoche sans outils ni colle.

Un accessoire pratique qui permet d’organiser votre réserve personnelle d’encoche et de les positionner rapidement sur votre tube. Disponible pour les encoches en version 1, 2 et Hunter.

The Beiter Push'n'Pull is the tool to install, turn or exchange asymmetric or symmetric Beiter Nocks.Thanks to the ergonomic styled grip, also hard moving nocks may be turned in and/or extracted from the shaft, without being damaged. The Beiter Push'n'Pull should be part of any archery tackle box, no matter if you are an archer or a coach!

Encoches AS pour tubes Carbone SUPER CLUB.

Disponibles en 5 couleurs : Rouge, Orange, Bleu, Verte et Crystal

Bohning's Blazer® Pin Nock was redesigned in 2019 to fit a broader range of pin sizes - redesigned nocks are easily identified as they are marked with the Bohning logo. The Blazer® Small Throat Pin Nock features a raised index and weighs an average of 5.0 grains (324 mg). Its .106" (2.69mm) throat size is designed to fit the small diameter bowstrings typically used by recurve shooters. Not sure which Bohning Pin Nock you have? The Blazer® Small Throat Pin Nock is marked with the letter "R" for easy identification. Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite wax to the pin.

Bohning's Blazer® Pin Nock was redesigned in 2019 to fit a broader range of pin sizes - redesigned nocks are easily identified as they are marked with the Bohning logo. The Blazer® Small Throat Pin Nock features a raised index and weighs an average of 5.0 grains (324 mg). Its .106" (2.69mm) throat size is designed to fit the small diameter bowstrings typically used by recurve shooters. Not sure which Bohning Pin Nock you have? The Blazer® Small Throat Pin Nock is marked with the letter "R" for easy identification. Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite wax to the pin.

Bohning's Smooth Release Pin Nock was redesigned in 2019 to fit a broader range of pin sizes - redesigned nocks are easily identified as they are marked with the Bohning logo. The Smooth Release Pin Nock features a raised index, short ears and a smooth throat for a clean release. Each nock weighs an average of 5.0 grains (324 mg). Its .120" (3.05mm) throat size is designed to fit larger diameter bowstrings typically used by compound shooters. Not sure which Bohning Pin Nock you have? The Smooth Release Pin Nock is marked with the letter "M" for easy identification. Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite wax to the pin.

Werner Beiter has invented the Asymmetric Nock! Not only: he was the first, that was able to produce specific nocks in different shapes for most arrows on the market! He developed Insert-Nocks, Outnocks, InOut-Nocks and PinOut-Nocks, to be used directly in or on shafts or on Bushings or Pins. Now Werner Beiter introduces the first Asymmetric Pin Nock, to complete the product line. The Beiter Pin-Nock is available in the Beiter patented ASYMMETRIC version, as well as in the SYMMETRIC version, for Compound archers using a D-Loop. Pay attention that the Beiter Logo should face on top of the nock while shooting!

Bohning's F Nock fits micro shafts with an ID of .166" (commonly known as 4mm or G Nock) shafts and G UNI Bushing systems. The F Nock features a double-lock throat of .120" (3.05mm). Each F Nock weighs an average of 6.5 grains (421.2 mg). Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite Wax to the nock shank. At Bohning, every nock style must pass the following steps before introduction to the market: 1. Computer simulations identify potential weak points. 2. Destructive testing methods expose possible design flaws or material defects. 3. Accelerated life cycle testing using a custom-built bow is performed at kinetic energy levels exceeding 110 ft-lbs (nearly twice that of most hunting bows). A single nock must withstand over 1000 shots or it goes back to step 1.

Bohning's F Nock fits micro shafts with an ID of .166" (commonly known as 4mm or G Nock) shafts and G UNI Bushing systems. The F Nock features a double-lock throat of .120" (3.05mm). Each F Nock weighs an average of 6.5 grains (421.2 mg). Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite Wax to the nock shank. At Bohning, every nock style must pass the following steps before introduction to the market: 1. Computer simulations identify potential weak points. 2. Destructive testing methods expose possible design flaws or material defects. 3. Accelerated life cycle testing using a custom-built bow is performed at kinetic energy levels exceeding 110 ft-lbs (nearly twice that of most hunting bows). A single nock must withstand over 1000 shots or it goes back to step 1.

Bohning's F Nock fits micro shafts with an ID of .166" (commonly known as 4mm or G Nock) shafts and G UNI Bushing systems. The F Nock features a double-lock throat of .120" (3.05mm). Each F Nock weighs an average of 6.5 grains (421.2 mg). Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite Wax to the nock shank. At Bohning, every nock style must pass the following steps before introduction to the market: 1. Computer simulations identify potential weak points. 2. Destructive testing methods expose possible design flaws or material defects. 3. Accelerated life cycle testing using a custom-built bow is performed at kinetic energy levels exceeding 110 ft-lbs (nearly twice that of most hunting bows). A single nock must withstand over 1000 shots or it goes back to step 1.

Bohning's F Nock fits micro shafts with an ID of .166" (commonly known as 4mm or G Nock) shafts and G UNI Bushing systems. The F Nock features a double-lock throat of .120" (3.05mm). Each F Nock weighs an average of 6.5 grains (421.2 mg). Tech tip: for easier insertion and indexing, apply a small amount of Bohning's Tex-Tite or Seal-Tite Wax to the nock shank. At Bohning, every nock style must pass the following steps before introduction to the market: 1. Computer simulations identify potential weak points. 2. Destructive testing methods expose possible design flaws or material defects. 3. Accelerated life cycle testing using a custom-built bow is performed at kinetic energy levels exceeding 110 ft-lbs (nearly twice that of most hunting bows). A single nock must withstand over 1000 shots or it goes back to step 1.